- Commonly Asked For Parts

#PartDescription ReqNotesAvailability
1 220-2056 36V lithium Ion battery
2 220-5148 Lithium battery charger
3 193-9115 Drive board (pkg of 2)
4 193-9080 Clean tank blow molding
5 193-9078 Recovery tank
6 193-9088 Ball shut off assembly
7 220-2132 Separator port molding [440NX]
8 193-9116 Pad red (pkg 10)
9 193-9117 Pad white (pkg of 10)
10 193-9118 Pad green (pkg of 5)
11 193-9119 Pad melamine (pkg of 2)
12 193-9120 Pad diamond (pkg of 2)

- Frequently Replaced Parts

#PartDescription ReqNotesAvailability
220-2056 36V lithium Ion battery
220-5148 Lithium battery charger
193-9043 Handle vac/water switch kit
193-9044 Handle safety switch kit
193-9054 Snap action switch kit
193-9014 Water solenoid
193-9093 Right hand valve assembly
193-9094 Left hand valve assembly
193-2098 Solenoid valve
193-9010 Port filter disc (pkg of 5)
193-9076 Port filter disc
193-9034 Blade set
193-9078 Recovery tank
193-9088 Ball shut off assembly
193-9022 Gasket seal molding (package of 4)
193-9035 Hose
193-9013 Vacuum motor kit
193-9114 Scrub brush nylon (pkg of 2)

Ball Shut Off Assembly

#PartDescription ReqNotesAvailability
1 193-2112 Ball system mount moulding 1
2 193-2113 Ball cage 1
3 193-2114 Ball support pillar 1
4 193-2115 Pillar end cap 1
5 193-2116 Pillar spring lock pin 1
6 193-2117 Ball 1
7 193-2118 Bearing 2
8 193-2119 Hollow ball and spring 1

Base Assembly

#PartDescription ReqNotesAvailability
1 193-2007 Screw 8 x 1/2 inch stainless steel 4
2 193-2074 Vent cap moulding 2
3 193-2075 Tube clip 2
4 193-9040 Left hand motor cover molding 1
5 193-9041 Right hand motor cover molding 1
6 193-9063 Screw 9
7 193-2087 Yoke 1
8 193-2079 Vac motor moulding 1
9 193-2084 Pad disc foam 1
10 193-2080 Vac motor top 1
11 193-2083 Gasket 2
12a 193-9013 Vacuum motor kit 1
12b 193-9155 Vacuum motor 1
13 193-2081 Vac motor middle casing 1
14 193-2082 Vac motor bottom moulding 1
15 193-9016 Center cover molding 1
16 193-2076 Grill 1
17 193-2088 Cable tie 2
18 193-9012 Brush motor kit 2
19 193-2105 Clevis pin 2
20 193-2104 Bolt hex head 2
21 193-2145 Washer 2
22a 193-2103 Latch 2
22b 193-2064 CSD deck casting 1
23 193-9156 Screw 2
24 193-1738 Nylon insert nut 1
25 193-0149 Washer M6-A stainless steel 9
26 193-2091 Screw block 11
27 193-9056 Bearing 1
28a 193-2085 Left and right hand link arm assembly 1 (includes 28 and 29)
28b N/A Not available 1 (Left deck link arm casting)
29 N/A Not available 1 (Right deck link arm casting)
30 193-9157 Handle position stop block 2
31 999-1609 Bolt M6-1 x 90mm hex head stainless steel 2
32 193-1994 Washer M5 stainless steel 4
33 193-2067 Left hand deck wing moulding 1
34 193-2066 Right hand deck wing moulding 1
35 193-2106 Cable tie (white) 9
36 193-2069 Buffer wheel 2
37 193-2070 Washer 2
38 193-1057 Screw #8 x 1 plastite 12
39 193-2098 Solenoid valve 2
40 193-2111 2mm closed cell disc neoprene 2
41 220-0332 Screw M4 x 8mm pozi pan head stainless steel 4
42 193-2099 Solenoid connector 2
43a 193-2108 P clip 1
43b 193-2107 P clip 1
44 193-2090 Grommet nut nylon 2
45 193-9158 Screw M5 x 16mm 6
46 193-2077 36v left hand bldc motor controller 1
47 193-9159 Blind grommet 1
48 193-2078 36v right hand bldc motor controller 1
49 193-9160 Deck casting 1
50 193-0205 Washer M5-A stainless steel 10
51 193-1022 Nut M5 nyloc stainless steel 8
52 193-9161 Latch plate right hand 1
53 193-1753 Trigger compression spring 2
54 193-9162 Bearing mounting plate 1
55 193-1876 Screw 2
56 193-9163 Latch plate left hand 1
57 193-9126 Rjump split housing 1
58 193-2109 Trim guide moulding 2
59 193-2065 Trim extrusion 1
60a 193-2101 Squeegee lift mechanism assembly (OBSOLETE) 1 (N/A as a kit. Must order 193-3109, 193-3110, 193-3111)
60b 193-9164 Squeegee and lifting mechanism assembly 1
61 193-9165 Extension spring 2
N/S 193-2068 Washer 12mm plastic 2
N/S 193-2089 Wheel 160mm x 50mm 1
N/S 193-2092 Left hand arm clip moulding 1
N/S 193-2093 Right hand arm clip moulding 1
N/S 193-2094 Reed switch assembly 1
N/S 193-2095 Reed switch clip 1
N/S 193-2096 Cable tie 1
N/S 193-2097 Magnet 1
N/S 193-9074 Wire clamp molding 1
N/S 193-2102 Spring 2
N/S 193-2110 Foot 1

Front Assembly

#PartDescription ReqNotesAvailability
6 193-9080 Clean tank blow molding 1
7 193-9006 Dual hose clip 1
9 220-2132 Separator port molding [440NX] 1
10 193-9008 Deck trim extrusion 1
11 193-9009 Trim glides 2
12 193-9010 Port filter disc (pkg of 5) 5
13 193-9011 Handle protection strip 2
18 193-9078 Recovery tank 1
20 193-9012 Brush motor kit 1
21 193-9013 Vacuum motor kit 1
22 193-9014 Water solenoid 1
25 193-9015 Deck wing kit 1
27 193-9017 Battery/control pbc kit 1
29 193-9016 Center cover molding 1
34 193-9022 Gasket seal molding (package of 4) 1
35 193-9019 Front handle cover 1
36 193-9021 Handle grip and trigger 1
37 193-9020 Handle adjust and release controls 1
38 193-9018 Grill molding 1
39 193-9024 Motor vent cover kit 2
43 193-9023 Tube clip 4
45 193-9029 Water tank support kit 1
46 193-9030 Clean water tank cap kit 1
48 193-9031 Drive board padlock clip with center molding kit 1
50 193-9032 Battery and base support molding kit 1
52 193-9033 O-ring kit 2
N/S 193-9025 Color coding kit (red) 1
N/S 193-9026 Color coding kit (blue) 1
N/S 193-9027 Color coding kit (green) 1
N/S 193-9028 Color coding kit (yellow) 1

General View Assembly

#PartDescription ReqNotesAvailability
1a 193-9127 Handle assembly 1 (Model 913433)
1b 193-9128 Handle assembly - Telematics 1 (Model 915764)
2 N/A Not available 1 (Mid section)
3 193-9129 Battery 1
4 193-0421 Hose 2
5 193-9130 Squeegee assembly (silver) 1
6 193-9131 Base assembly 1

Handle Assembly

#PartDescription ReqNotesAvailability
1 193-2120 Handle cross tube 1
2 193-2121 Handle grip 2
3 193-2122 Handle trigger 2
4 193-2123 Handle release lever 1
5 193-2124 Handle lock button (red) 1
6 193-1787 Switch 2
7 193-1753 Trigger compression spring 3
8 193-2125 Handle front cover moulding 1
9a 193-2126 Handle rear cover moulding 1 (913337 Only)
9b 193-9132 Rear cover moulding 1 (Telematics-915763 only)
10 193-2127 Handle PC8 enclosure 1
11 193-2128 Illuminated toggle switch 2
12 193-2129 Handle wiring protector 1
13 193-9133 Push button switch (yellow) 1
14 193-1023 Screw #8 x 5/8 plastite stainless steel 8 (Torque to 2.6Nm)
15 193-9134 Domed protective strip 1
16 193-9135 Telematics module assembly 1 (913337 Only)
17 193-9136 Adhesive pad 1 (915763 and 918986 Only)
18 193-1057 Screw #8 x 1 plastite 4 (915763 and 918986 Only)
20 193-9138 Front handle cover 1
21a 193-9139 Rear handle cover 1 (918985 Only)
21b 193-9140 Rear handle cover - Telematics 1 (918986 Only)
22 193-9141 Telematics module assembly (black) 1 (918986 Only)
23 193-9142 Hour meter (black) 1 (919505 Only)
24 193-9143 Hour meter (grey) 1 (919504 Only)

Rear Assembly

#PartDescription ReqNotesAvailability
2 193-9036 Squeegee assembly 1
3 193-9037 Squeegee wheel set 3
4 193-9038 Squeegee retaining knob 2
5 193-9089 Rear cover assembly 1
14a 193-9035 Hose 1
14b 193-0421 Hose 1
15 193-9040 Left hand motor cover molding 1
16 193-9041 Right hand motor cover molding 1
17 193-2172 Hose cuff 1
19 193-9045 Rear wheel kit 1
23 193-9043 Handle vac/water switch kit 1
24 193-9044 Handle safety switch kit 1
26 193-9046 Handle pcb kit 1
28 193-9047 Tap assembly kit 1
30 193-9098 Floor tool trap molding 1
31 193-9048 Floor tool trap clip 1
32 193-9049 Floor tool end caps 1
33 193-9034 Blade set 1
40 193-9052 Handle tube with clips 1
41 193-9051 Right hand motor controlle kit 1
42 193-9097 Left hand motor controller 1
44 193-9050 Floor tool bracket 1
47 193-9055 Floor tool latching kit 1
49 193-9053 Pitch latch kit 1
51 193-9054 Snap action switch kit 1

Squeegee and Lifting Mechanism Assembly

#PartDescription ReqNotesAvailability
1a 193-2130 Floor tool release pedal 1
1b 193-3113 Hub moulding 2
2 193-9107 Axle 1
3 193-0177 Screw M4 x 16mm pan head stainless steel 3
4 193-0194 Washer M4-A stainless steel 7
5 193-0176 Nut M4 nylon insert stainless steel 3
6 193-2133 Bolt M8 x 25 2
7 193-3112 Pedal plate 1
8 193-2134 Foot pedal 2
9 193-2135 Washer 2
10 193-1255 Nut nylon 2
11 193-9109 Tapered cap (red) 2
12 193-2136 Shoulder bolt 2
13 193-2137 Thrust washer 2
14 193-9110 Nylon spacer 10.1 mm id x 15 mm od x 6.5mm 2
15 193-9111 Igus bearing 4
16 193-2138 Screw M6 x 20mm 4
17 193-1807 Washer 4
18 193-0149 Washer M6-A stainless steel 6
19 193-9112 Floor tool link arm 2
20 193-9113 Squeegee pivot tube 1
21 193-2139 Compression spring 2
22 193-2140 Floor tool plate 1
23 193-2141 Bolt M6 x 16 2
24 193-2142 Lifting pin 2
25 193-2143 Axle support weldment 1
26 193-2144 Washer 2
27 193-2145 Washer 2
28 193-2146 Support wheel 2
29 193-2147 Spacer 2
30 193-2148 Extension spring 2
31 193-1738 Nylon insert nut 2
32 193-2149 Spacer 2
33 193-2150 Spacer 2
34 193-2151 Bolt M6 x 30MM 2
35 193-2152 Screw M4 x 10mm 4
36 193-2153 Washer 4
37 193-2154 Bearing 4
38 193-2155 Rear linkage 2
39 193-2156 Spacer 6
40 193-2157 Bearing 3
41 193-2158 Connecting rod link shaft 2
42 193-2159 Connecting rod 1
43 193-2160 Shaft bearing 1
44 193-2161 Extension spring 1
45 193-2162 Front caster assembly 1
N/S 193-2131 Floor tool latch core 1
N/S 193-1801 Screw 1
N/S 193-2132 Spacer 1
N/S 193-9108 Floor tool pedal plate 1

Squeegee Assembly

#PartDescription ReqNotesAvailability
1a 193-3114 Squeegee outer die casting (silver) 1 (911916 only)
1b 193-3115 Outer squeegee moulding 1 (918093 only)
1c 193-2163 Outer squeegee die casting 1
2a 193-2164 Inner squeegee moulding for die casting 1 (911916 only)
2b 193-3116 Inner squeegee moulding 1 (918093 only)
3 193-2165 Squeegee wheel 3
4 193-2166 Finishing washer (black) 2
5 193-9034 Blade set 1
6 193-9034 Blade set 1
7 193-2169 Squeegee seal extrusion 1
8 193-1738 Nylon insert nut 2
9 193-2171 Snap lock pin 3
10 193-2172 Hose cuff 1
11 193-1374 Screw M5 x 35mm hex head 2
12 193-2173 Screw 3.5 x 12mm 2
13 193-2007 Screw 8 x 1/2 inch stainless steel 2
14a 193-2174 Left hand floor tool clip 1 (911916 only)
14b 193-3117 Left hand floor tool clip - NUC420 (black) 1 (918093 only)
15 193-2069 Buffer wheel 2
16a 193-2175 Right hand floor tool clip 1 (911916 only)
16b 193-3118 Right hand floor tool clip - NUC420 1 (918093 only)
17a 193-2176 Hose trap inlet 1 (911916 only)
17b 193-3119 Hose trap inlet 1 (918093 only)
18 193-2177 Hose trap clip 1
19 193-2178 Squeegee knob 2
20a 193-1375 Screw M6 x 25mm pozi pan head (OBSOLETE) 2
20b 193-2170 Bolt M6 x 20mm 2
21 193-3120 Squeegee snap plate 2
N/S 193-2145 Washer 2
N/S 193-9098 Floor tool trap molding 1 (includes 7 and 20a)

Tank Assembly

#PartDescription ReqNotesAvailability
1 220-2132 Separator port molding [440NX] 1 (includes 2-4)
3 220-2132 Separator port molding [440NX] 1
4 193-9076 Port filter disc 1
5 193-9088 Ball shut off assembly 1
6 193-9078 Recovery tank 1
7 193-9022 Gasket seal molding (package of 4) 1
8 193-9070 Cap with vent hole molding 1
9 193-9071 Tether molding 1
10 193-9080 Clean tank blow molding 1
11 193-9091 Check valve tank coupling (pkg of 2) 2
12 193-2007 Screw 8 x 1/2 inch stainless steel 10
13 193-9083 Water tank shelf molding 1
14 193-9087 Foam pad 1
15a 193-9082 Water tank support molding 1
15b 193-9144 Water tank support molding 1
16 193-9084 Battery support molding 1
17 193-9017 Battery/control pbc kit 1
18 193-9145 Compression spring 2
19a 193-9085 22 inch clear silicone tube 2
19b 193-9146 24 inch clear silcone tube 2
20 193-9147 Hose retainer 1
21 193-9059 Washer 2
22 193-9094 Left hand valve assembly 1
23 193-9093 Right hand valve assembly 1
24 193-9063 Screw 1
25 193-9074 Wire clamp molding 1
26 193-9086 Retainer plate 1
27a 193-9069 Handle base section molding 1
27b 193-9148 Handle base printed white water flow 1
28 193-1738 Nylon insert nut 3
29 193-0149 Washer M6-A stainless steel 4
30 193-9064 Handle release slider 1
31 193-9072 Handle locking rod 1
32 193-9092 Handle tube (silver) 1
33a 193-9066 Tank lock molding 1 (includes 54)
33b 193-9149 Wrap-around tank lock housing 1
34a 193-9067 Hose end mount molding 1
34b 193-9150 Wrap-around hose end 1
35a 193-9068 Dual hose clip molding 2
35b 193-9151 Wrap-around dual hose clip 2
35c 193-9166 Hose mount clip kit 1 (includes 54)
36 193-9089 Rear cover assembly 1
37 193-1878 Bolt 2
38 193-1745 Half nut 1
39 193-9090 Cross dowel barrel nut 1
40 193-9061 Handle pivot molding (black) 2
41 193-9056 Bearing 4
42 193-9058 Bolt and nut cap 1
43 193-1255 Nut nylon 1
44 193-1889 Washer 1
45 193-9062 Spring 1
46 193-9065 Roll latch 1
47 193-1258 Washer 1
48 193-9057 Bolt M8 x 10 x 50 hex socket 1
49 220-0966 Cover shoulder bolt 1
50 193-9095 Clevis pin 1
51 193-9060 Pitch latch (black) 1
52 193-9096 E-clip 1
53 193-9152 Screw 6 x 3/8 1
54 193-9153 Nylon rivet (OBSOLETE) 8
55 193-9154 O-ring 1
N/S 193-9114 Scrub brush nylon (pkg of 2) 2

Wiring Diagram

#PartDescription ReqNotesAvailability
A21 220-4952 Loom assembly .4crt
A02 220-4951 Loom assembly .7crt
A03 220-5160 Loom assembly 7crt