- KAWASAKI FH500/FH541 - Muffler - Dust Bonnet - Emission System

#PartDescription ReqNotesAvailability
001a 170-3218 Kawasaki dust bonnet 1 (OEM)
001b 991-8592 Kawasaki bonnet filter 1 (NON-OEM)
002 170-3219 Bonnet cage 1
003 170-3237 Bonnet cage gasket 1
004 N/A Not available 1 (Emission system)
005a 170-3230 Exhaust manifold 1
005b 170-2005 Exhaust manifold 1 (Models 08992B and 08993B)
006 154-0175 Muffler clamp (OBSOLETE) 1
007a 270-0048 Vertical muffler non-catalytic 1
007b 170-3232 Vertical mount catalytic converting muffler (OBSOLETE) 1
008 N/A Not available 1 (Oxygen sensor)

- Pad Holders

#PartDescription ReqNotesAvailability
1 991-2214 Center-Lok II pad holder - left hand thread (red)
2a 991-2201 Center-Lok II pad holder - right hand thread (black) (Pad driver side female, Floor side male)
2b 991-8577 Pad retainer (Pad driver side male, Floor side female)
3a 991-2202 Big mouth pad holder set (blue) (includes 3 screws)
3b 991-2205 Deep lock ring and pad grip ring
4 991-2203 Big mouth pad holder male thread portion
5 991-2206 Center-Lok 3 pad holder (includes 3 screws)
6 996-0372 Big mouth pad holder (left hand thread)
7 N/A Not available
8 991-2209 Split retainer - pad holder ring (OBSOLETE)
9 N/A Not available (replaced by #3 991-2202)
10 991-2211 Center lock pad holding cup (male) (yellow) (OBSOLETE)

-Engine- Kawasaki FS481V

#PartDescription ReqNotesAvailability
001 178-0329 Bolt 12 x 30 1
002 178-0135 Washer 1 (DS10 only)
003 178-0137 Woodruff key 1
004 178-7107 Flywheel assembly 1
005 189-5152 Propane emission decal 1
006 189-0392 Screw #10 x 5/8 pan head phillips 2
007a 189-8544 Emissions shutdown module with oxygen sensor 1 (Betco)
007b 154-1042 SafeSense emission monitoring module retro kit 1 (Pioneer)
008a 189-3090 Oil dipstick 1 (Plastic oil dipsticks are only good for a short time because the last couple inches of the dipstick are always in oil and will eventually stain, get brittle, and then break off inside the engine due to the high heat of the oil. The pieces of plastic can cause problems inside the engine and the only way to get them out is to remove the crankcase, which is very labor intensive.)
008b 154-0367 Kawasaki dipstick 1
009a 178-0306 Dipstick tube 1
009b 178-0016 O-ring 2
010 178-0265 Voltage regulator 1
011 178-0330 Wire lead 1
012 178-0331 Screw 2
013 178-0123 Flanged bolt 4
014 178-7106 Electric starter 1
015a 178-0264 Ignition coil assembly Kawasaki FS481V 2
015b 991-7143 Ignition coil assembly 2 (NON-OEM)
016a 166-0008 Spark plug (Kawasaki FS481V) 2
016b 178-7104 Spark plug wiring harness 1
017 178-0280 Intake manifold 1
018a 178-0255 Air pre-filter 1 (OEM)
018b 991-6028 Air pre-filter 1 (NON-OEM)
019a 178-0256 Air filter 1 (Betco) (OEM)
019b 991-6029 Air filter 1 (NON-OEM)
019c 178-0256 Air filter 1 (Kawasaki)
019d 178-7207 Air filter assembly with prefilter 1 (Kawasaki)
020 178-0281 Hose clamp 1
021 178-0282 Hose 1
022 178-0279 Air filter case 1
023 178-0278 O-ring 2
024 178-0277 Thumb nut 2
025 178-0283 Hose clamp 1
026a 178-0290 Carburetor assembly 1 (Pioneer, Nilfisk, Kawasaki)
026b 189-5148 Carburetor aluminum block (keep internal parts of old carb) 1 (Betco)
027 178-0284 Stud bolt 2
028 178-0332 Plug 1
029 178-0333 Clamp 1
030 178-0195 Flanged nut 2
031 178-0334 Intake pipe 1
032 178-0042 Carb intake gasket 2
033 178-0257 Gasket 2
034 178-0036 Exhaust stud bolt 4
035 178-0335 Bolt 6 x 12 7
036 178-7108 Breather cover 1
037 178-0263 Breather gasket 1
038 189-8452 J clip stamped hook 1
039 178-7109 Breather pipe 1
040 178-0151 Screw pan head 1
041 178-7110 Breather plate 1
042 178-7111 Breather valve 1
043 178-0043 Top oil seal (upper crankshaft - Kawasaki) 1
044a 178-0113 Plug 1
044b 178-0010 Oil drain adapter 1
044c 178-0016 O-ring 2
045a 178-0254 Oil filter 1 (OEM)
045b 991-6027 Oil filter 1 (NON-OEM)
046 154-0143 Oil pressure switch with 2 prongs 1
047 178-0206 Clamp 1
048 178-7012 Plug 1
049 178-0336 Crankcase complete 1 (includes 50)
050 178-0337 Joint 1
051 178-0302 O-ring 1
052 178-0338 Pipe 3
053 178-0273 Dowell pin 6
054 178-0261 Cylinder head gasket (FS481V engine only) 2
055a 178-0304 #1 right cylinder head assembly (FS481V) 1 (Includes (1) rocker cover gasket, (2) valve springs, (1) intake valve, (1) exhaust valve, (1) cylinder head gasket, (1) intake gasket, (1) exhaust gasket, (2) exhaust studs)
055b 178-0258 Right (while operating) bare cylinder head #1 1
055c 178-0305 #2 left cylinder head assembly (FS481V) 1 (Includes (1) rocker cover gasket, (2) valve springs, (1) intake valve, (1) exhaust valve, (1) cylinder head gasket, (1) intake gasket, (1) exhaust gasket, (2) exhaust studs)
055d 178-0259 Left (while operating) bare cylinder head #2 1
056 178-0272 Head bolt 14
058 178-0339 Lift hook 1
059 178-0032 Valve stem seal 4
060 178-0124 Bolt 6 x 25 flange 10
061a 178-7112 Rocker case (cylinder #2) 1
061b 178-7113 Rocker case (cylinder #1) 1
062 178-0262 Rocker case gasket 2
064 178-0272 Head bolt 14
065 178-0036 Exhaust stud bolt 4
066 178-0271 Head bolt 6
067 999-1489 Screw 3/8-16 x 1 1/2 hex head stainless steel 4
068 999-0034 Washer 3/8 split lock plain finish 4
069 178-0260 Bottom oil seal 1
071 178-0236 Plug 2
073 178-0340 Plug 1
074 178-0084 Oil seal 1
075 178-0322 Crankcase cover 1
076 178-0338 Pipe 3
077 178-0273 Dowell pin 6
078 204-0071 Bolt 1
079 999-0120 Washer 3/8 SAE flat 1
080 189-8544 Emissions shutdown module with oxygen sensor 1 (Betco)
081 189-5147 Nut 1
082a 169-0142 Muffler plug 1 (Pioneer)
082b 991-1601 Oxygen sensor 1 wire (OBSOLETE) 1
083a 189-3087 Catalytic muffler and manifold assembly 1 (Betco)
083b 154-1044 Catalytic muffler and manifold assembly (Kawasaki FS481V) 1 (Pioneer)
084 178-0286 Fan housing kit 1
090 178-7133 Bolt 4
091 178-0386 Washer 4
092 178-0098 Collet (valve keeper) (sold individually - need 2 per valve) 8
093 178-0048 Valve retainer ring 4
094 178-0276 Valve spring 4
095 178-0270 Intake valve 2
096 178-0045 Lifter 4
097 178-0268 Push rod 4
098 178-0269 Exhaust valve 2
099 178-7134 Nut 4
100 178-0353 Bracket 4
101 178-0384 Bolt 8 x 14 flange 4
102 178-7132 Collar 4
103 178-0383 Rocker arm 4
KIT 050-0007 Kawasaki FS481V 100 hour kit 1 (includes oil filter, pre-air filter, air filter and spark plug)
N/S 189-8544 Emissions shutdown module with oxygen sensor 1
N/S 991-1810 Compression tester 1
N/S 991-1832 Emission tester 1
N/S 178-0402 Throttle control plate 1
N/S 178-0313 Charging coil (stator) 1
N/S 178-0275 Spring 1
N/S 178-0316 Fan 1
N/S 991-4039 Spark plug tester 1

Carrier Assembly

#PartDescription ReqNotesAvailability
2 999-0170 Nut 3/8-16 hex plain finish 2
3 999-0032 Washer 3/8 USS flat plain finish 2
4 270-0033 Spacer 3/16 black 2
6 999-1371 Bolt 1/2 x 3/8 shoulder stainless steel 2
7 999-0032 Washer 3/8 USS flat plain finish 8
8 999-0170 Nut 3/8-16 hex plain finish 4
9 270-0035 Carrier weldment 1
11 999-0152 Nut 1/4-20 nylon insert lock zinc plated 6
12 999-0016 Washer 1/4 flat plain finish 6
13 999-0081 Screw 1/4-20 x 5/8 pan head slotted zinc 6
14 999-0038 Bolt 3/8-16 x 1 hex head grade 5 zinc plated 4

Control Box Assembly

#PartDescription ReqNotesAvailability
1a 169-0016 Key switch assembly with two keys 1
1b 991-1901 Key 1
2a 170-0052 Hour meter 1 (OEM)
2b 991-7137 Hour meter 1 (NON-OEM)
3 170-1971 Control box weldment 1
4 162-0006 12V 18Ah AGM battery (size 6) 1
5 170-1972 Control box cover 1
6 999-0321 Screw 10-32 x 3/8 pan head slotted zinc plated 7
7 270-0036 PBU decal 1
8 999-0016 Washer 1/4 flat plain finish 2
9 999-0152 Nut 1/4-20 nylon insert lock zinc plated 2
10 170-1974 Carb guard circuit board with three lights (OBSOLETE) 1
11 170-3062 12V starter solenoid 1
12 999-0323 Screw 1/4-20 x 1/2 pan head slotted zinc plated 2
13 999-0463 Screw 6-32 x 3/8 pan head slotted zinc plated 4
14 170-1975 Carb guard decal (OBSOLETE) 1
15 270-0037 Bushing 1
16 270-0038 Bushing (OBSOLETE) 1

Drive, Wheel and Frame Assembly

#PartDescription ReqNotesAvailability
1 164-1015 Washer 1 x .13 thick flat 7
2 170-3142 Centrifugal clutch 1
3 154-0016 Bottom clutch spacer 1
4 999-0044 Washer 7/16 medium split lock 1
5 999-0853 Screw 7/16-20 x 2 hex head grade 5 plain finish 1
6 170-3075 Square keyway 1
7 170-8944 01-09.5j21 1
12 270-0041 Spacer 1
13 170-2414 Washer flat 1
14 999-0659 Washer 3/8 medium split lock stainless steel 1
15 999-0390 Bolt 3/8-16 x 2 1/2 hex hd grade 5 zinc plated 1
16 999-0109 Bolt 5/16-18 x 1 1/2 hex head grade 5 zinc plated 12
17 170-1988 Burnisher deck mounting gasket 2
18 170-1989 Gasket (OBSOLETE) 1
19 N/A Not available 1 Vacbox casting (Gray)
20 999-0170 Nut 3/8-16 hex plain finish 3
21 999-0659 Washer 3/8 medium split lock stainless steel 3
22 999-0649 Bolt 3/8-16 x 1 1/4 hex head stainless steel 3
23 170-1991 Caster weldment 2
24a N/A Not available 1 27 inch drive housing casting
24b N/A Not available 1 21 inch drive housing casting
25 999-0016 Washer 1/4 flat plain finish 14
26 999-0211 Nut 5/16-18 hex nylon insert lock zinc plated 12
27 170-1994 5 inch wheel 4
28 170-1995 Cotter pin with clevis pin 2
29 999-0211 Nut 5/16-18 hex nylon insert lock zinc plated 2
30 999-0032 Washer 3/8 USS flat plain finish 4
31 999-0638 Bolt 3/8-16 x 2 1/4 hex head 2
N/S 372-1150 Spindle assembly 1 (PBU 21KACAT)

Dust Containment Assembly

#PartDescription ReqNotesAvailability
1 170-1978 Filter lid assembly (OBSOLETE) 1
2 170-1979 Dust filter (OBSOLETE) 1
4a 170-9018 27 inch bumper (OBSOLETE) 1
4b 270-0039 21 inch bumper 1
4c 170-1981 Dust control bumper skirt 7.5 ft
5a 170-9019 27 inch skirt assembly 1
5b 270-0040 21 inch skirt assembly 1
6 170-1984 Wire tie 2
7 170-1985 Dust boot 1
8 170-1986 Dust plug in 1
KIT 170-1982 27 inch dust skirt kit (OBSOLETE) 1 Includes 4A, 5A, 170-7876, 170-1984, rivets and screws
KIT 170-1983 21 inch skirt assembly 1 Includes 4B, 5B, 170-7877, 170-1984, rivets and screws

Engine - Kawasaki FH381V

#PartDescription ReqNotesAvailability
1 178-0137 Woodruff key 1
2 178-7114 Flywheel 1
4 178-0023 Voltage regulator 1
5 178-7115 Charging coil 1
6 178-0104 Spring 1
7 178-7116 Camshaft assembly 1
8 178-7081 120V electric starter 1 (includes 9 and 10)
9 N/A Not available 1 (Starter gear assembly)
10 178-7117 Armature 1
11a 178-0014 Plastic Kawasaki dipstick 1
11b 178-0016 O-ring 1
12a 178-0003 Oil filter Kawasaki 1 (OEM)
12b 991-7117 Oil filter 1 (NON-OEM)
14 178-7118 Stud bolt 2
15 178-7101 Ignition coil assembly 1
17 166-0004 Spark plug (Kawasaki FH500V/FH541V/FH381V) 2
18a 154-0143 Oil pressure switch with 2 prongs 1 (Pioneer)
18b 170-3221 Oil pressure switch, 3-prong molded plug 1 (Alto-Clarke)
18c 372-3186 Adapter 1 (Alto-Clarke)
19a 178-7096 Carburetor 1
19b 178-0042 Carb intake gasket 1
21 170-3241 Spud kit 1 (Alto-Clarke)
22a 178-7085 Air filter element 1
22b 178-0222 Air filter 1
23 178-0223 Pre-filter 1
24 178-7071 Front air filter case 1
25 178-7073 Rear air filter case 1
27 178-7119 Breather plate and gasket 1
28 178-0043 Top oil seal (upper crankshaft - Kawasaki) 1
29 178-7120 Crankcase 1
30 178-7121 Crankcase cover 1
31 178-0084 Oil seal 1
32 178-0033 Bottom oil seal 1
33 178-7092 Cylinder head gasket 2
34a 178-7099 Bare cylinder head #1 1
34b 178-7100 Bare cylinder head #2 1
35a 178-0013 Rocker cover gasket 2 (OEM)
35b 991-7072 Valve cover gasket 2 (NON-OEM)
36 178-0078 Rocker case 2
37 178-0076 Rocker arm 2
38 178-0047 Valve spring 2
39 178-0030 Intake valve 1
40 178-0029 Exhaust valve 1
41 178-0010 Oil drain adapter 1
42 154-0362 Oil drain valve 1 (Pioneer)
43 154-0037 Tubing 1/2 x 5/8 (clear) (sold by the foot) 1 ft
44 154-0038 Oil drain cap 1 (Pioneer)
45 178-0129 Spark plug wiring harness 1
46 178-7080 13 HP crankcase cover gasket 1
N/S 178-0287 Intake manifold 1
N/S 178-7022 Intake manifold gasket 1
N/S 270-0757 Catalytic muffler 1 (Alto-Clarke)
N/S 154-3432 Catalytic muffler and manifold assembly 1 (Pioneer)
N/S 169-0142 Muffler plug 1
N/S 178-0001 Exhaust manifold gasket 2
N/S 991-1601 Oxygen sensor 1 wire (OBSOLETE) 1
N/S 154-0008 Electric clutch assembly 1 (Pioneer clutch models)
N/S 178-7097 Fuel filter 1
N/S 991-1810 Compression tester 1
N/S 991-1832 Emission tester 1
N/S 154-1042 SafeSense emission monitoring module retro kit 1 (Pioneer)
N/S 991-6002 12V fuel lock off (Model 152) 1
N/S 991-6001 Fuel regulator (T60) 1
N/S 170-2003 Catalytic converter muffler (OBSOLETE) 1
KIT 050-0113 Kawasaki FH381V 100 hour kit 1 (includes oil filter, pre-air filter, air filter and spark plug)
N/S 991-4039 Spark plug tester 1

Engine - Kawasaki FH500v/FH541V

#PartDescription ReqNotesAvailability
207a 178-0003 Oil filter Kawasaki 1 (OEM)
207b 991-7117 Oil filter 1 (NON-OEM)
217 999-0024 Washer 5/16 flat stainless steel 8
219 178-0004 Long rear stud 2
222 178-0006 Short front stud 2
228 999-0211 Nut 5/16-18 hex nylon insert lock zinc plated 4
229 154-0143 Oil pressure switch with 2 prongs 1
233 999-0673 Nut M6-1 acorn zinc plated 4
238 178-0043 Top oil seal (upper crankshaft - Kawasaki) 1
239 178-0010 Oil drain adapter 1
240 178-0016 O-ring 1
241a 178-0211 Left (while operating) cylinder head assembly (FH500V) 1 (This is an assembled cylinder head. Gaskets are included. You will need to reuse your rocker arms and rocker arm studs. Includes (1) 178-0013, (2) 178-0047, (1) 178-0030, (1) 178-0029, (1) 178-0028, (1) 178-0035, (1) 178-0001, (2) 178-0036, and (2) 178-0032)
241b 178-0212 Right (while operating) cylinder head assembly (FH500V) 1 (This is an assembled cylinder head. Gaskets are included. You will need to reuse your rocker arms and rocker arm studs. Includes (1) 178-0013, (2) 178-0047, (1) 178-0030, (1) 178-0029, (1) 178-0028, (1) 178-0035, (1) 178-0001, (2) 178-0036, and (2) 178-0032)
241c 178-7181 Left (while operating) cylinder head assembly (FH541V) 1 (This is an assembled cylinder head. Gaskets are included. You will need to reuse your rocker arms and rocker arm studs. Includes (1) 178-0013, (2) 178-0047, (1) 178-0030, (1) 178-0029, (1) 178-7038, (1) 178-0035, (1) 178-0001, (2) 178-0036, and (2) 178-0032)
241d 178-7180 Right (white operating) cylinder head assembly (FH541V) 1 (This is an assembled cylinder head. Gaskets are included. You will need to reuse your rocker arms and rocker arm studs. Includes (1) 178-0013, (2) 178-0047, (1) 178-0030, (1) 178-0029, (1) 178-7038, (1) 178-0035, (1) 178-0001, (2) 178-0036, and (2) 178-0032)
241e 178-0013 Rocker cover gasket 2 (OEM)
241f 991-7072 Valve cover gasket 2 (NON-OEM)
241g 178-0030 Intake valve 2
241h 178-0029 Exhaust valve 2
241i 178-0028 Cylinder head gasket (FH500V engine only) 2
241j 178-7038 Cylinder head gasket (FH541V engine only) 2
241k 178-0035 Intake gasket 2
241l 178-0001 Exhaust manifold gasket 2
241m 178-0036 Exhaust stud bolt 4
241n 178-0032 Valve stem seal 4
242 154-0042 Oil drain valve kit 1
243 154-0037 Tubing 1/2 x 5/8 (clear) (sold by the foot) 1 ft
244 164-0398 Control valve (white clamp) 1
245 178-0020 Air filter clip (includes swivel) 2 (includes 259)
246a 178-0014 Plastic Kawasaki dipstick 1
246b 154-0367 Kawasaki dipstick 1
246c 178-0015 Dipstick tube (OBSOLETE) 1
246d 178-0016 O-ring 1
246e 178-0123 Flanged bolt 1
247 178-0021 Fan housing 1
248 N/A Not available 1 (Starter gear assembly)
249a 178-0024 Ignition coil assembly Kawasaki FH500V/FH541V 2 (OEM)
250 166-0004 Spark plug (Kawasaki FH500V/FH541V/FH381V) 2
257a 160-0083 Starter solenoid (remote mounted) 1
257b 991-9257 SOLENOID -STARTER 12V (NON-OEM)
258a 178-0025 12V starter assembly kit (Kawasaki FH500V & FH541V engines) 1 (Entire starter assembly, includes reference 248)
258b 178-7081 120V electric starter 1 (110V start units)
259 N/A Not available 2 (Swivel) (included with 245)
260 178-0023 Voltage regulator 1
264 164-1536 Spacer (OBSOLETE) 2
265 999-0744 Screw 10-32 x 1 3/4 pan head phillips zinc plated 2
266 999-0053 Washer #10 split lock plain finish 2
267 999-0412 Washer #8 SAE flat 2
268 160-0141 Stud M6 x 130 2
269 164-1538 Rubber cap (OBSOLETE) 1
270 178-0042 Carb intake gasket 2
271 160-0115 Fuel load block 1 (Eagle specific)
272 178-0195 Flanged nut 2
273 160-0116 Brass plug 1/8 1
274 160-0117 Elbow 3/8 x 1/4 mp 1
275 165-0012 Spark plug boot (OBSOLETE) 2
276 178-0129 Spark plug wiring harness 1
280 178-0085 Bolt 6 x 12 flanged 1 (old style)
281a 178-0079 Breather cover and gasket kit 1 (old style)
281b 178-7039 Plate 1 (old style)
282 178-0307 Cover and gasket kit 1 (old style)
284 178-0043 Top oil seal (upper crankshaft - Kawasaki) 1
285 178-0036 Exhaust stud bolt 4
286 178-0081 Crankcase complete 1
287 178-0017 Crankcase gasket 1
288 178-0082 Snap ring 2
289 178-0083 Pin 6
290a 178-0028 Cylinder head gasket (FH500V engine only) 2
290b 178-7038 Cylinder head gasket (FH541V engine only) 1
291 178-0032 Valve stem seal 4
292 178-0078 Rocker case 2
293 178-0060 Bolt 6 x 40 flange 4
294a 178-0013 Rocker cover gasket 2 (OEM)
294b 991-7072 Valve cover gasket 2 (NON-OEM)
295 178-0087 Flanged bolt 2
296a 178-0027 Left (while operating) bare cylinder head 1 See 178-0211 or 178-7181 for head assembly
296b 178-0026 Right (while operating) bare cylinder head 1 See 178-0212 or 178-7180 for head assembly
297 178-0086 Flanged bolt 8
299 178-0080 Crankcase cover (OBSOLETE) 1
300 178-0084 Oil seal 1
301 178-0033 Bottom oil seal 1
302 178-0309 Breather cover (new style) 1 (new style)
303 178-0308 Breather gasket (new style) 1 (new style)
304 178-0310 Bolt flanged 14mm 1 (new style)
305 178-7002 Air filter assembly 1 (includes 306-310)
306a 178-7004 Air filter case assembly 1
306b 178-0041 Air cleaner rear housing (includes filters and gasket) 1
307a 178-0005 Air pre-cleaner Kawasaki 1 (OEM)
307b 991-7118 Pre-filter (green) 1 (NON-OEM)
308 178-0019 Air filter cover 1
309a 178-0007 Air filter Kawasaki 1 (OEM)
310 178-0197 Nut 1
N/S 050-0006 Kawasaki 100 hour service kit 1
N/S 154-0269 Carbon monoxide safety patch (OBSOLETE) 1
N/S 991-9251 CO DETECTOR 1 (NON-OEM option to 154-0269)
N/S 170-2004 Isolator (OBSOLETE) 5 (for dust control units)
N/S 170-3235 Support bracket 1
N/S 170-3259 Nut M6 x 2 hex 4
N/S 178-0039 Push rod 4
N/S 189-8544 Emissions shutdown module with oxygen sensor 1 (original shut-down system has been made unavailable. This part will need additional wiring that is not included.)
N/S 991-1601 Oxygen sensor 1 wire (OBSOLETE) 1
N/S 991-1810 Compression tester 1
N/S 991-1832 Emission tester 1
N/S 999-0565 Screw 10 x 3/4 pan head phillips sheet metal 2 (not included in kit)
N/S 154-0412 Carburetor for Kawasaki (OBSOLETE) 1 (Pioneer)
N/S 154-0250 Muffler bracket 1 (Super Buffer)
N/S 991-4039 Spark plug tester 1
KIT 050-0006 Kawasaki 100 hour service kit 1 (includes oil filter, pre-air filter, air filter and spark plug)

Fuel Assembly

#PartDescription ReqNotesAvailability
1a 161-0003 Aluminum propane tank 1
1b 161-0004 Steel propane tank 1
2 991-6004 Female quick coupler 1
3 170-3180 3/8 inch propane hose 1
4 991-6015 12V fuel lock off (Model 121) 1
5 160-0054 45 degree elbow fitting 2
6 170-1784 Elbow 1/4 (OBSOLETE) 1
7 991-6001 Fuel regulator (T60) 1
8 997-2002 Hose clamp #6 2
9 170-3120 Hose barb elbow 1
10 170-7873 3/8 inch hose assembly with insert 1
11 991-1403 Vacuum hose (sold by the foot) 2.5 ft
13 170-3055 1/4 hex nipple 1
14 160-0052 Fitting 1/4 barb x 1/4mp 1
15 999-0323 Screw 1/4-20 x 1/2 pan head slotted zinc plated 2
16 170-3181 Check valve 1

Handle Assembly

#PartDescription ReqNotesAvailability
1 170-7875 Handle 1
2 170-1970 Pin assembly (OBSOLETE) 2
3 170-3660 60 inch throttle cable Kawasaki 17 (OBSOLETE) 1
4 170-3021 Handle grip tube 1
5 170-3018 Lever bar 1

NON-OEM Dust Bonnet and Cage Option

#PartDescription ReqNotesAvailability
1 991-9014 Kawasaki dust bonnet 1
2a 160-0198 3 tab filter cage with support ring for 17HP (metal) 1 (includes 2b)
2b 160-0297 Filter cage support ring for 17HP (converts 3 tab/4 tab) 1
3 999-0250 Bolt M5-.8 x 10mm hex head full thread 3 (to secure cage to ring)
4 999-0740 Nut M5-.8 hex stainless steel 3 (to secure cage to ring)
5 999-0673 Nut M6-1 acorn zinc plated 4 (to secure ring to engine)
6 999-0123 Washer 1/4 SAE flat zinc plated 7 (to secure cage and ring to engine)
7 160-0123 3 tab filter cage for 18HP (metal) 1

Pad Driver Assembly

#PartDescription ReqNotesAvailability
1 999-0043 Bolt 7/16-20 x 1 1/4 hex head grade 5 zinc plated 4
2 999-0044 Washer 7/16 medium split lock 4
3 170-0304 Washer 15/32 x 1/32 4
4 170-1996 Bearing assembly (OBSOLETE) 1
5 170-3072 7.5 inch pulley (OBSOLETE) 1
6 170-3075 Square keyway 1
7 999-0854 Washer 3/4 external lock zinc plated 1
8a 170-1997 21 inch pad driver assembly 1
8b 189-8297 27 inch pad driver assembly flex 1
9 999-0678 Screw 8-18 x 5/8 pan head self-drilling stainless steel 3
10 170-3102 21 inch pad driver assembly steel 1
N/S 170-1998 B-47 v-belt 1
N/S 991-2206 Center-Lok 3 pad holder 1